View previous topic :: View next topic |
Author |
Message |
Bertolom New Member
Joined: 05 Dec 2006 Posts: 6 Location: Santa Claus, IN
|
Posted: Wed Dec 06, 2006 12:00 am Post subject: Mitsubishi 520m DNC setup |
|
|
Found this on the web, so I wanted to put it here.
Machine: Mitsubushi
Communications Settings:
Properties page
Setting Value
DNC-HUB Std PC Ports (or HUB # if installed)
Port Depends on Computer
Baud 4800
Bits 7
Parity Even
Stop Bits 2
XON/XOFF Send/Recv
Use RTS/CTS Off
Local Echo On
Auto On
ANSI Codes Off
Machine Page
Leader Len 5
Code ISO
Start Send Blank
End Send Blank
Start Recv Blank
End Recv Blank
Advanced Page
CR in None
LF in None
CR out None
LF out None
EOF Timeout 30 (varies)
Char Delay 0
Line Delay 0
Wait for XON ON
Protocol ASCII
Machine Control Setup Instructions:
Set up a three letter I/O device name under I/O device Param (1) , using parameter #1
I/O Device Param (1)
#2 Baud Rate = 2 -- (4800)
#3 Stop Bit = 3 -- (2 stop bits)
#4 parity Effective = 0 -- (not during I/O)
#5 Even Parity = 1 -- (Even)
#6 Chr Length = 3 -- (8 bits)
#7 Termination Type = 3 -- (EOR)
#11 Handshake = 3 -- (DC code)
#12 DC code parity = 1 -- (parity added)
I/O Device Param (2)
#1 DC2/DC4 Output = 1 -- (with DC2 no DC4)
#2 CR output = 1 -- (on)
#3 EIA output = 0 -- (ISO Output)
#6 Parity C = 0 -- (off)
#7 Time-Out = 300 -- (30 seconds)
Cable Diagram:
Standard Cable
Notes:
Standard Cable
Standard Cable configurations
7 Wire cables with Hardware Handshaking
Computer 25 Pin connector(Typically Female on Cable) Machine Tool 25 Pin Connector(Typically Male on Cable)
2 3
3 2
4 5
5 4
7 7
20 6
6 20 & 8
Computer 9 Pin connector(Typically Female on Cable) Machine Tool 25 Pin Connector(Typically Male on Cable)
2 2
3 3
4 6
5 7
6 20 & 8
7 5
8 4
3 Wire cables without Hardware Handshaking
Computer 25 Pin connector(Typically Female on Cable) Machine Tool 25 Pin Connector(Typically Male on Cable)
2 3
3 2
4 & 5 Tied Together 4 & 5 Tied Together
7 7
20 & 6 Tide Together 6 & 8 & 20 Tied Together
Computer 9 Pin connector(Typically Female on Cable) Machine Tool 25 Pin Connector(Typically Male on Cable)
2 2
3 3
4 & 6 Tied Together 4 & 5 Tied Together
5 7
7 & 8 Tied Together 6 & 8 & 20 Tied Together
________
BOX VAPORIZERS
Last edited by Bertolom on Wed Feb 16, 2011 5:33 am; edited 1 time in total |
|
Back to top |
|
|
mistux Site Admin
Joined: 25 Jun 2004 Posts: 1042 Location: South Bend, Indiana USA
|
Posted: Wed Dec 06, 2006 2:37 pm Post subject: |
|
|
Thanks for the information, I'm sure someone eventually will be able to use it.
It is nice to see people shairing their kndowledge |
|
Back to top |
|
|
|