Manufacturing Information Solutions Forum Index Manufacturing Information Solutions
Your Place for Support and Discussions
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Hurco MB - I / MB - I H Tool Changer Error Messages

 
Post new topic   Reply to topic    Manufacturing Information Solutions Forum Index -> CNC Controls
View previous topic :: View next topic  
Author Message
mistux
Site Admin


Joined: 25 Jun 2004
Posts: 1042
Location: South Bend, Indiana USA

PostPosted: Thu Jun 09, 2005 3:38 pm    Post subject: Hurco MB - I / MB - I H Tool Changer Error Messages Reply with quote

Hurco MB - I / MB - I H Tool Changer Error Messages:



Detailed tool loading and automatic tool changer information is included in Section 3 of your Owner’s Manual. This addendum describes additional safety features and the tool changer error detection and reporting system.

While the Z-axis is involved in changing a tool with the tool magazine under the spindle, the Rapid Traverse rate is set to a maximum of 100 IPM. (The parameter page may be used to set the rapid traverse less than 100 IPM.)

The microcomputer tests the various electrical sensors and limit switches to determine what state the tool changer is in. If, during tool changer operation, the microcomputer detects an incorrect state or state change, an EMERGENCY STOP condition will result with the message " TOOL CHANGER ERROR nn ". " nn " is an error code, which indicates the reason for the Emergency Stop Condition. This two-digit error code, in almost all cases, identifies the particular limit switch.

The following is a list of the possible error codes and their condition. Click on "Error Code" Number or "Scroll Page" for explanation. To return here, click Error Code Number above "Condition."

Error Code: 84 60 61 62 63 64 65 66 67 68 69 25 27 06 07 26



ERROR CODE: 84

CONDITION: " Arm back " not detected, or both " arm front " and " arm back " was detected.
1) Checked when axis is calibrated, jogged or moving in the auto program mode.
2) Checked when spindle manual control is exercised.
3) Checked in auto tool changer mode.

ERROR CODE: 60

CONDITION: The current tool number is zero (0) and there is a tool in the spindle.

ERROR CODE: 61

CONDITION: There is a tool in the tool magazine at the current tool number location.

ERROR CODE: 62

CONDITION: During a tool change while the Z-axis is moving, the spindle must be unclamped or the error code is displayed.

ERROR CODE: 63

CONDITION: Once the "shot pin" solenoid is energized during a tool change, a check for the "shot pin in" limit switch is made for the rest of the tool change. If this limit switch is not seen, the error code is displayed.

ERROR CODE: 64

CONDITION: While moving the tool magazine arm in to "get a tool" or "put a tool" in the spindle, during tool change, a check is made for the "magazine-in-position" switch. If not detected, the error code is displayed.

ERROR CODE: 65

(Applies to the MB - 1H only.)
CONDITION: Before the "shot pin" solenoid is energized, an orientation speed check is made to determine if the speed is less than 60 RPM.
1) Checks for spindle reference input.
2) Checks for spindle speed less than 60 RPM.
* Any of the above can cause the error to be displayed.

ERROR CODE: 66

CONDITION: Before the "shot pin" solenoid is energized, a check for the drive monitor signal (DM) is made. If not detected, the error code is displayed.

ERROR CODE: 67

CONDITION: While the tool magazine arm is in (front), a check for the "arm in" limit switch is made during any Z-axis movement. If not seen, the error code is displayed.

ERROR CODE: 68

CONDITION: If the tool magazine is requested to rotate and no rotation takes place, the error code will be displayed.

ERROR CODE: 69

CONDITION: If the tool magazine is rotating and a non - sequential tool number is detected, the error code will be displayed.


Each time a normal tool change function is performed, a check for that function's limit switch is performed. If not detected, one of the following errors will occur.

ERROR CODE: 25

CONDITION: "Shot pin" in; "Shot pin" out; Same limit switch.

ERROR CODE: 27

CONDITION: Drive monitor (DM) off.


ERROR CODE: 06

CONDITION: Arm pivot in.

ERROR CODE: 07

CONDITION: Arm pivot out.

ERROR CODE: 26

CONDITION: Spindle "clamp;" Spindle "unclamp;" Same limit switch.
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    Manufacturing Information Solutions Forum Index -> CNC Controls All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group