|
Manufacturing Information Solutions Your Place for Support and Discussions
|
View previous topic :: View next topic |
Author |
Message |
franke Master Poster
Joined: 26 Jun 2004 Posts: 161 Location: Indiana, USA
|
Posted: Wed Jul 14, 2004 12:40 pm Post subject: Problem with Thread deburring |
|
|
I have a lot of trouble deburring (blunting) threads at the beginning and at the end of them. The G-codes that I do are generally for 1/6" pitch rounded threads on a HAAS SL-30 lathe (supposed to have Fanuc6T controller or similar).
Any ideas about how to make a G-code for "cleaning" the start and finish portion of the thread
I'm working on SL-30 Big Bore......it's not mine, though...
The beginning of a thread is "sharp" and needs to be "flattened", so it would look better and nobody could cut himself while twisting it in his hands...here's a sample of a sequence I use for making an OD thread:
G99 M24
X72.2 Z0
M19 P180
G97 S400 M03
G76 D0.8 X65. Z-19. K2.5 F4.23
This cycle is making an almost perfect 70mm thread with 4.23 pitch (1/6"). I do the spring pass afterwards.
In this case I am using M24, but when I do IDs I use M23.
I have tried different "P" and "X" settings, but to no avail. Never thought about changing "Z", though......I wonder whether a grooving insert would follow the same thread lead if I change "Z".
I have tried to do the deburring operation in a tapered way (with an “I” command), but without any success.
If it would be not much trouble to you, please contact me on: _________________ --------------------------
Thanks for everything. |
|
Back to top |
|
|
CNCJimmy7 Frequent Poster
Joined: 05 Jul 2004 Posts: 91 Location: Minneapolis, MN
|
Posted: Wed Jul 14, 2004 12:43 pm Post subject: |
|
|
Here is a clipped 3 pitch acme male thread.
Code: |
(3 PITCH ACME)
G54
G00 G53 X0 Z-14.
G50 S3000
M41
T303
G00 G97 S150 M03
X4.315 Z0.0889 M08 (start position of thread--in front of part)
M24
G76 X3.753 Z-1.75 (length of thread) K0.177 A14 D0.008 F0.3333
G00 X4.315 Z0.1605
M09
G00 G53 X0 Z-14.
M01
(THIS CYCLE WILL COMPLETELY REMOVE (FLATTEN)THE THE VERY START OF THE THREAD. IF DONE LIKE THIS EXAMPLE, YOU SHOULD BE ABLE TO RUB A BABY'S REAR ON THE STARTING THREAD AND NOT CUT HIM)
(THREAD CLIP 3 PITCH ACME)
(.187 WIDE V84 GROOVING INSERT)
G54
G00 G53 X0 Z-14.
G50 S1500
M41
T213
G00 G97 S150 M03
X4.315 Z0.27 M08 (start position in front of part)
M24
G76 X3.761 Z-0.275 (length of 1st thread to clip)K0.177 D0.008 F0.3333
G00 X4.315 Z0.1605
M09
G00 G53 X0 Z-14.
|
|
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|