Manufacturing Information Solutions Forum Index Manufacturing Information Solutions
Your Place for Support and Discussions
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Genie PCG650 Garage Door Opener Programming

 
Post new topic   Reply to topic    Manufacturing Information Solutions Forum Index -> Nothing In Particular
View previous topic :: View next topic  
Author Message
mistux
Site Admin


Joined: 25 Jun 2004
Posts: 1042
Location: South Bend, Indiana USA

PostPosted: Sun Aug 16, 2009 4:18 pm    Post subject: Genie PCG650 Garage Door Opener Programming Reply with quote

Model 2: Intellicode Model GWKP (off-white with flip-up cover)

Programming Instructions for the GWKP Genie garage door opener keyless entry involves following the two sets of steps below:
1. To erase the old PIN (personal identification number) press and hold down, in order, the "PROG," "6" and "Up/Down Arrow" keys. The red LED will blink once and then turn off. Release the buttons.
2. To program: press, in order, but do not hold down the "3," "5," "7" and "PROG" keys.
3. Enter your chosen PIN, anywhere from 3 to 8 characters.
4. Press "PROG" (red LED blinks - twice per second and turns off)
Find the Learn Code Button and the LED indicator light on your Genie motor head inside the garage. It is usually behind the light lens and close to the floppy antenna wire. If your Door Opener does not have an antenna, you have an External Receiver. The External Receiver cover must be removed to access the Learn Code button and the indicator LED. Follow Steps 1 through 3 outlined below:
1. Press this Learn Code button momentarily. The red LED indicator light will start to blink. It will blink for up to 30 seconds. While it is blinking:
2. Enter your PIN and press the "Up/Down Arrow" key on your keypad. The Learn Code Indicator LED will stay on.
3. Press the "Up/Down Arrow" key again. The Learn Code indicator LED turns off. Wait until the Keypad backlight turns off (approximately 30 seconds).
4. Test by entering your PIN and pressing the "Up/Down Arrow" key to operate your door.
Multiple Genie Garage Door Opener Programming for GWKP- All garage doors will use the same PIN:
1. Enter PIN and press PROG (red LED blinks once per second).
2. press PROG again (red LED blinks twice per second).
3. press the number of doors you wish to control (2 key or 3 key).
4. press PROG (red led blinks several times and turns off).
5. Decide which Door will be Door #1, #2, and #3.
6. Press the Learn Code Button on the motor head.
7. Enter your PIN and press the Up/Down key on the Keypad.
8. Press the number you have picked for this Door Opener (key 1, 2 or 3)
9. Press the Up/Down key.
10. Repeat steps 6 through 9 for each Door Opener.
To make a copy, highlight area and copy into your word program. You can then print out a legible copy of the chart and programming steps from your word software.
Programming Instructions for Genie remotes:
Programming Genie Intellicode Remote Transmitters

1. Press the Receiver Learn Code button on the power head receiver of your door operator. This small, black, unmarked button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the motor head. When pressed, a radio signal indicator light will start blinking red for 30 seconds. **
2. After pressing the Learn Code Button once, press your transmitter button three times for your system to grab the frequency and code it in. (Keep the transmitter you want tuned at least 2 feet away from the power head while tuning.)
3. Press the transmitter button once more to test the system and start your door moving.
**To erase all Intellicode remotes and wireless keyless entry, hold down on the learn button until the indicator light stops blinking, then proceed to Step 2.
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic   Reply to topic    Manufacturing Information Solutions Forum Index -> Nothing In Particular All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group