Manufacturing Information Solutions Forum Index Manufacturing Information Solutions
Your Place for Support and Discussions
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

RS232C setting of Mitsubishi Meldas 520AM

 
Post new topic   Reply to topic    Manufacturing Information Solutions Forum Index -> CNC Controls
View previous topic :: View next topic  
Author Message
BIGmiralli
Frequent Poster


Joined: 17 Apr 2007
Posts: 38
Location: Boston, Massachusetts

PostPosted: Tue Apr 17, 2007 2:11 pm    Post subject: RS232C setting of Mitsubishi Meldas 520AM Reply with quote

We are installing a DNC connection to Meldas 520AM, but we have a problem with the settings.

Can anyone help me to set the Parameters and cable configurations of the 520AM?

Thanks so very much.
________
BOX VAPORIZER


Last edited by BIGmiralli on Wed Feb 16, 2011 10:38 am; edited 1 time in total
Back to top
View user's profile Send private message
choseung-hui
New Member


Joined: 17 Apr 2007
Posts: 4
Location: Tokyo, Japan

PostPosted: Tue Apr 17, 2007 2:14 pm    Post subject: Reply with quote

Machine: Mitsubushi

Communications Settings:

Properties page

Setting Value

DNC-HUB Std PC Ports (or HUB # if installed)
Port Depends on Computer
Baud 4800
Bits 7
Parity Even
Stop Bits 2
XON/XOFF Send/Recv
Use RTS/CTS Off
Local Echo On
Auto On
ANSI Codes Off


Machine Page

Leader Len 5
Code ISO
Start Send Blank
End Send Blank
Start Recv Blank
End Recv Blank

Advanced Page

CR in None
LF in None
CR out None
LF out None
EOF Timeout 30 (varies)
Char Delay 0
Line Delay 0
Wait for XON ON

Protocol ASCII


Machine Control Setup Instructions:

Set up a three letter I/O device name under I/O device Param (1) , using parameter #1

I/O Device Param (1)
#2 Baud Rate = 2 -- (4800)
#3 Stop Bit = 3 -- (2 stop bits)
#4 parity Effective = 0 -- (not during I/O)
#5 Even Parity = 1 -- (Even)
#6 Chr Length = 3 -- (8 bits)
#7 Termination Type = 3 -- (EOR)
#11 Handshake = 3 -- (DC code)
#12 DC code parity = 1 -- (parity added)


I/O Device Param (2)
#1 DC2/DC4 Output = 1 -- (with DC2 no DC4)
#2 CR output = 1 -- (on)
#3 EIA output = 0 -- (ISO Output)
#6 Parity C = 0 -- (off)
#7 Time-Out = 300 -- (30 seconds)


Cable Diagram:


Standard Cable

Notes:
Standard Cable

Standard Cable configurations

7 Wire cables with Hardware Handshaking

Computer 25 Pin connector(Typically Female on Cable)
Machine Tool 25 Pin Connector(Typically Male on Cable)
2 3
3 2
4 5
5 4
7 7
20 6
6 20 & 8


Computer 9 Pin connector(Typically Female on Cable)
Machine Tool 25 Pin Connector(Typically Male on Cable)
2 2
3 3
4 6
5 7
6 20 & 8
7 5
8 4


3 Wire cables without Hardware Handshaking


Computer 25 Pin connector(Typically Female on Cable)
Machine Tool 25 Pin Connector(Typically Male on Cable)
2 3
3 2
4 & 5 Tied Together 4 & 5 Tied Together
7 7
20 & 6 Tide Together 6 & 8 & 20 Tied Together


Computer 9 Pin connector(Typically Female on Cable)
Machine Tool 25 Pin Connector(Typically Male on Cable)
2 2
3 3
4 & 6 Tied Together 4 & 5 Tied Together
5 7
7 & 8 Tied Together 6 & 8 & 20 Tied Together
Back to top
View user's profile Send private message
BIGmiralli
Frequent Poster


Joined: 17 Apr 2007
Posts: 38
Location: Boston, Massachusetts

PostPosted: Tue Apr 17, 2007 2:18 pm    Post subject: Reply with quote

Very Happy
Wow, that was fast Exclamation

Thanks, I will give it a try.
________
Arizona dispensary
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic   Reply to topic    Manufacturing Information Solutions Forum Index -> CNC Controls All times are GMT - 5 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group