View previous topic :: View next topic |
Author |
Message |
reddado67 New Member
Joined: 20 Oct 2005 Posts: 4
|
Posted: Sat Oct 22, 2005 2:38 am Post subject: To activate parameter 901 bit 5 |
|
|
My question is following:
How it is possible to activate parameter 901 bit 5 in a Fanuc 0mc?
Thanks
Reddado67 |
|
Back to top |
|
|
mistux Site Admin
Joined: 25 Jun 2004 Posts: 1042 Location: South Bend, Indiana USA
|
Posted: Mon Oct 31, 2005 1:47 pm Post subject: |
|
|
Not completely sure what you are asking.
Can you even get to the 901 parameter?
Let us know. If you can, I can look up the the methond of changing it. |
|
Back to top |
|
|
reddado67 New Member
Joined: 20 Oct 2005 Posts: 4
|
Posted: Thu Nov 03, 2005 10:33 am Post subject: |
|
|
Parameter 901 bit 5 is that one of the corner or chamfer but if I try to go to modify the bit, it does not come modified also activating the possibility to modify the parameters. |
|
Back to top |
|
|
mistux Site Admin
Joined: 25 Jun 2004 Posts: 1042 Location: South Bend, Indiana USA
|
Posted: Thu Nov 03, 2005 11:25 am Post subject: |
|
|
Can you modify any of the paramters anywhere?
There is a procedure for allowing you to change parameters. If that is it, I will look up in my notes for that. |
|
Back to top |
|
|
reddado67 New Member
Joined: 20 Oct 2005 Posts: 4
|
Posted: Fri Nov 04, 2005 4:11 am Post subject: |
|
|
therefore there is a procedure if I have understood well for being able to modify the parameter? |
|
Back to top |
|
|
dawn Master Poster
Joined: 26 Jun 2004 Posts: 311 Location: Mishawaka, IN
|
Posted: Mon Nov 07, 2005 11:20 am Post subject: |
|
|
Mode switch set to MDI
touch Param button
Param button
Page down once (you should see PWE Enable)
change to 1
Alarm is activated (Parameter "write enable" switch on)
Param button
page down, cursor down to #0901
***write down the current value***
...Carfully overwrite the whole number...
you will find that the first bit on the right is bit "0" and the last one on the left is bit "7".
#7 #6 #5 #4 #3 #2 #1 #0
Be extremely careful when doing this! Be absolutely sure what you are changing!
Last go back to the PWE setting and change it back to 0.
(Disables parameter writing) |
|
Back to top |
|
|
reddado67 New Member
Joined: 20 Oct 2005 Posts: 4
|
Posted: Wed Nov 09, 2005 3:27 am Post subject: |
|
|
Thanks
Dario R. |
|
Back to top |
|
|
Allbert Guest
|
Posted: Mon Dec 12, 2005 10:44 am Post subject: |
|
|
I have 901 #1 as meaning 120m of tape length (memory), and bit #0 is 320m |
|
Back to top |
|
|
mroy0404 New Member
Joined: 14 Mar 2006 Posts: 12
|
Posted: Wed Sep 06, 2006 10:22 pm Post subject: Fanuc OT/OM |
|
|
If you are trying to get more memory from this control I can help.
Email me at mroy7@cogeco.ca |
|
Back to top |
|
|
|