Manufacturing Information Solutions Forum Index Manufacturing Information Solutions
Your Place for Support and Discussions
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Search found 12 matches
Manufacturing Information Solutions Forum Index
Author Message
  Topic: 1990 Hitachi Seiki HT20SII CNC Lathe
mroy0404

Replies: 2
Views: 17753

PostForum: Lathes   Posted: Wed Jul 08, 2009 9:16 pm   Subject: 1990 Hitachi Seiki HT20SII CNC Lathe
SOLD!!
  Topic: FS 1995 Daewoo Puma 8s
mroy0404

Replies: 0
Views: 6720

PostForum: Lathes   Posted: Wed Jul 08, 2009 9:15 pm   Subject: FS 1995 Daewoo Puma 8s
Offered for sale is this very well kept, meticulously maintained DAEWOO/PUMA 8-S 2-axes Slant Bed CNC Turning Center, S/N PM8S 0274 New 1995

Max. swing over carriage 12.2”
Max. turning diameter 14 ...
  Topic: 1990 Hitachi Seiki HT20SII CNC Lathe
mroy0404

Replies: 2
Views: 17753

PostForum: Lathes   Posted: Thu Nov 01, 2007 9:59 pm   Subject: Offers
Guys

I still have this CNC lathe, and open to offers.

mroy7@cogeco.ca

Mike Roy

1 519 337 0423
  Topic: Fanuc Only Forum
mroy0404

Replies: 1
Views: 13604

PostForum: Suggestions   Posted: Thu Oct 11, 2007 9:02 pm   Subject: Fanuc only forum
This site should have a fanuc only forum, this will help people find and answer fanuc problems.
  Topic: 1990 Hitachi Seiki HT20SII CNC Lathe
mroy0404

Replies: 2
Views: 17753

PostForum: Lathes   Posted: Wed Jun 20, 2007 7:12 pm   Subject: 1990 Hitachi Seiki HT20SII CNC Lathe
Hi Guys

Offered for sale is this very well kept, meticulously maintained Hitachi Seiki HT20SII.

Machine Specs: Royal collet nose, 8.25 max turn diameter, Two inch bar capacity, X travel @ 7.9 in ...
  Topic: Hitachi Seiki HT20SII CNC Lathe
mroy0404

Replies: 3
Views: 15262

PostForum: CNC Controls   Posted: Wed Apr 25, 2007 2:19 pm   Subject: Hitiahi alarm
Thanks for the reset, it worked.

But I still have another alarm on the CRT it says 5022 spindle driver alarm, and on the spindle amp in the back it has a (# 33 over voltage alarm) would you know h ...
  Topic: Hitachi Seiki HT20SII CNC Lathe
mroy0404

Replies: 3
Views: 15262

PostForum: CNC Controls   Posted: Wed Mar 28, 2007 11:08 am   Subject: Hitachi Seiki HT20SII CNC Lathe
Hi Guys

I bought this CNC lathe that has a PC not ready alarm on a Seicos LB Mark II control. Has anyone seen this problem before and repaired it.What are the possible causes for this alarm.
I kno ...
  Topic: Fanuc 10M with no tape mode switch
mroy0404

Replies: 2
Views: 12265

PostForum: CNC Controls   Posted: Sun Jan 14, 2007 6:40 pm   Subject: Fanuc 10m
Hi Guy

I have the same problem with a fanuc 10m(no tape mode)I have found a CNC retro fitter to change the eprom. I have not sent my chips to him yet. I'am thinking we could send our chips to him a ...
  Topic: Fanuc OT-C
mroy0404

Replies: 2
Views: 10992

PostForum: CNC Controls   Posted: Tue Sep 19, 2006 8:34 am   Subject: Fanuc OT-C
Hi Guys

Today I turned on the CNC lathe (Fanuc OT-C) as normally and the CRT was rolling or scrolling vary fast then began to slow down to a stop (took about 1 min.). This has never happened before ...
  Topic: To activate parameter 901 bit 5
mroy0404

Replies: 8
Views: 22388

PostForum: CNC Controls   Posted: Wed Sep 06, 2006 10:22 pm   Subject: Fanuc OT/OM
If you are trying to get more memory from this control I can help.
Email me at mroy7@cogeco.ca
  Topic: Fanuc 10m dripfeed (DNC)
mroy0404

Replies: 6
Views: 20582

PostForum: CNC Controls   Posted: Mon Mar 20, 2006 1:07 pm   Subject: Fanuc 10m
I have come to find out that 410 pages of memory is the max. for this control(fanuc 10m modal A)I started out with 195 pages of mem. if any of you guys want to increase the mem. on their control email ...
  Topic: Fanuc 10m dripfeed (DNC)
mroy0404

Replies: 6
Views: 20582

PostForum: CNC Controls   Posted: Sun Mar 19, 2006 9:01 pm   Subject: Fanuc 10m
Hi billy

Have you fixed this problem as I have the same(no tape mode on the 10m) it is a BMI interface control.
With no programs, it has 410 pages of memory and 50 files. Could you tell me how muc ...
 
Page 1 of 1
All times are GMT - 5 Hours
Jump to:  


Powered by phpBB © 2001, 2005 phpBB Group