Author |
Message |
Topic: 1990 Hitachi Seiki HT20SII CNC Lathe |
mroy0404
Replies: 2
Views: 22376
|
Forum: Lathes Posted: Wed Jul 08, 2009 9:16 pm Subject: 1990 Hitachi Seiki HT20SII CNC Lathe |
SOLD!! |
Topic: FS 1995 Daewoo Puma 8s |
mroy0404
Replies: 0
Views: 7864
|
Forum: Lathes Posted: Wed Jul 08, 2009 9:15 pm Subject: FS 1995 Daewoo Puma 8s |
Offered for sale is this very well kept, meticulously maintained DAEWOO/PUMA 8-S 2-axes Slant Bed CNC Turning Center, S/N PM8S 0274 New 1995
Max. swing over carriage 12.2”
Max. turning diameter 14 ... |
Topic: 1990 Hitachi Seiki HT20SII CNC Lathe |
mroy0404
Replies: 2
Views: 22376
|
Forum: Lathes Posted: Thu Nov 01, 2007 9:59 pm Subject: Offers |
Guys
I still have this CNC lathe, and open to offers.
mroy7@cogeco.ca
Mike Roy
1 519 337 0423 |
Topic: Fanuc Only Forum |
mroy0404
Replies: 1
Views: 17891
|
Forum: Suggestions Posted: Thu Oct 11, 2007 9:02 pm Subject: Fanuc only forum |
This site should have a fanuc only forum, this will help people find and answer fanuc problems. |
Topic: 1990 Hitachi Seiki HT20SII CNC Lathe |
mroy0404
Replies: 2
Views: 22376
|
Forum: Lathes Posted: Wed Jun 20, 2007 7:12 pm Subject: 1990 Hitachi Seiki HT20SII CNC Lathe |
Hi Guys
Offered for sale is this very well kept, meticulously maintained Hitachi Seiki HT20SII.
Machine Specs: Royal collet nose, 8.25 max turn diameter, Two inch bar capacity, X travel @ 7.9 in ... |
Topic: Hitachi Seiki HT20SII CNC Lathe |
mroy0404
Replies: 3
Views: 16427
|
Forum: CNC Controls Posted: Wed Apr 25, 2007 2:19 pm Subject: Hitiahi alarm |
Thanks for the reset, it worked.
But I still have another alarm on the CRT it says 5022 spindle driver alarm, and on the spindle amp in the back it has a (# 33 over voltage alarm) would you know h ... |
Topic: Hitachi Seiki HT20SII CNC Lathe |
mroy0404
Replies: 3
Views: 16427
|
Forum: CNC Controls Posted: Wed Mar 28, 2007 11:08 am Subject: Hitachi Seiki HT20SII CNC Lathe |
Hi Guys
I bought this CNC lathe that has a PC not ready alarm on a Seicos LB Mark II control. Has anyone seen this problem before and repaired it.What are the possible causes for this alarm.
I kno ... |
Topic: Fanuc 10M with no tape mode switch |
mroy0404
Replies: 2
Views: 13367
|
Forum: CNC Controls Posted: Sun Jan 14, 2007 6:40 pm Subject: Fanuc 10m |
Hi Guy
I have the same problem with a fanuc 10m(no tape mode)I have found a CNC retro fitter to change the eprom. I have not sent my chips to him yet. I'am thinking we could send our chips to him a ... |
Topic: Fanuc OT-C |
mroy0404
Replies: 2
Views: 12067
|
Forum: CNC Controls Posted: Tue Sep 19, 2006 8:34 am Subject: Fanuc OT-C |
Hi Guys
Today I turned on the CNC lathe (Fanuc OT-C) as normally and the CRT was rolling or scrolling vary fast then began to slow down to a stop (took about 1 min.). This has never happened before ... |
Topic: To activate parameter 901 bit 5 |
mroy0404
Replies: 8
Views: 23710
|
Forum: CNC Controls Posted: Wed Sep 06, 2006 10:22 pm Subject: Fanuc OT/OM |
If you are trying to get more memory from this control I can help.
Email me at mroy7@cogeco.ca |
Topic: Fanuc 10m dripfeed (DNC) |
mroy0404
Replies: 6
Views: 21801
|
Forum: CNC Controls Posted: Mon Mar 20, 2006 1:07 pm Subject: Fanuc 10m |
I have come to find out that 410 pages of memory is the max. for this control(fanuc 10m modal A)I started out with 195 pages of mem. if any of you guys want to increase the mem. on their control email ... |
Topic: Fanuc 10m dripfeed (DNC) |
mroy0404
Replies: 6
Views: 21801
|
Forum: CNC Controls Posted: Sun Mar 19, 2006 9:01 pm Subject: Fanuc 10m |
Hi billy
Have you fixed this problem as I have the same(no tape mode on the 10m) it is a BMI interface control.
With no programs, it has 410 pages of memory and 50 files. Could you tell me how muc ... |
|